In essence, a water leaking fault is represented by the Samsung dishwasher error code LC. The sensors within the dishwasher are either detecting a water leak or moisture in an unexpected place if you receive this problem code. Water leakage is the most common cause of the problem.
But it could also be a problem with the sensors or the control panel, which can be remedied by turning the dishwasher on and off again. The Samsung dishwasher error code LC could also appear if the dispenser is overflowing with detergent. As shown throughout this book, various techniques can be utilized to resolve error code LC depending on the cause.
The Samsung Dishwasher error code LC indicates that the machine’s leak sensor is detecting an excessive amount of moisture, which is frequently brought on by a water leak. A faulty connection, water supply hose, or drain hose may leak moisture or water, resulting in the error code LC.
In this scenario, replacing the damaged component is required to resolve the LC error code on your Samsung dishwasher. The dishwasher can be powered off and on again to fix any software issues that may have caused this error. A defective leak sensor is one of the potential causes of error code LC.
Causes of the Samsung dishwasher error code LC
The error code LC typically appears during the wash cycle. The dishwasher will then abruptly stop and begin flashing the letters LC on the display when this occurs. When the LC error code is visible, you cannot operate or use the dishwasher.
Although the problem is typically brought on by moisture or water leaks, it can also be brought on by a number of other factors. The typical reasons of error code LC on Samsung dishwashers are covered below:
Water Spill
On Samsung dishwashers, this is probably the main reason why error code LC occurs. From faulty or damaged water line connections, moisture or water may be seeping. Additionally, the dishwasher’s filling valve or water output hose may leak.
Given this, it suggested to check the dishwasher for any indications of a water leak before attempting any other error code LC remedies.
Dispenser that is too full
You can only put a certain amount of dishwashing detergent into the dispenser at a time. On Samsung dishwashers, it has alson demonstrated that overfilling the dispenser results in error code LC. Suds that form from using too much detergent are more likely to fall to the bottom and activate the leak sensor.
The dishwasher being moved
If the dishwasher recently relocated, water may have splashed into or close to the leak sensor, resulting in error code LC. In this situation, you must unhook the dishwasher from the electrical outlet and give the water spilled on the counter plenty of time to dry out.
Connection error with a garbage disposal unit Simply by connecting your Samsung dishwasher to a garbage disposal machine, LC could also manifest itself. This is especially true if you don’t take off the disposal unit’s cap. If this turns out to be the issue, all you have to do to fix it is take off the cap.
Faulty door seal
Your dishwasher’s door may not close completely, allowing water to leak into the leak sensor from the bottom. As a result, you should also look for any damage to the sealing contour around the dishwasher door. The efficiency of the seal may also harmed by the presence of debris and grease.
Check to see if the dishwasher properly aligned if water is dripping from the bottom of the door, as detailed later in this tutorial.
Defective leak sensor
The leak sensor on your Samsung dishwasher could malfunction as well, though this is uncommon. When this occurs, the sensor can mistakenly identify the presence of moisture or a leak. If all other potential explanations have ruled out, your dishwasher’s leak sensor may need to replaced. This will resolve error code LC.
Fixing Error Code LC
Samsung dishwashers’ LC error code frequently caused by a circuit board issue. If so, restarting the dishwasher’s power supply should fix the problem. You must unplug the dishwasher from the outlet and leave it unplugged for roughly 15 minutes in order to accomplish this.
As a result, the dishwasher can reset as the capacitors can drain the charge. Reconnect the unit’s power and turn it on after 15 minutes. If the dishwasher’s error code returns after reset, the appliance seriously malfunctioning. In this instance, you must look over the drain hose, water supply, and leveling legs.
To begin with, you must look for any obvious leaks on the machine, particularly at the water supply pipe and both ends of the connectors. It advised to stop the flow of water if you discover a leak and utilize the following techniques to identify and remedy the issue:
Run a cycle to find the leak using method 1
The best technique to locate a dishwasher’s leak point is to feel and inspect the inside parts for moisture. The Leaking Point, however, can only be located after moisture or water has spilled. It is essential to run a test cycle on your dishwasher to check for leaks.
Simply start the device, connect it into an outlet, and conduct a test cycle. Close the dishwasher and unplug it from the power source when the cycle has finished. Now you must check the appliance for any leakage evidence or feel the interior parts for moisture.
Play Drive Mad with friends in your free time to relax and have some fun. Try out now for free!
